可拓法评估煤矿瓦斯爆炸易发性

为了量化煤矿瓦斯爆炸的可能性,并为防治瓦斯爆炸提供量化指标,借鉴可拓学原理,对煤矿瓦斯爆炸易发性进行预评估。首先,详细阐述可拓学评估原理;接着,为了验证煤矿瓦斯爆炸易发性可拓评估的可行性,结合某一煤矿实例,比选煤矿瓦斯爆炸易发性的评价指标,并确定煤矿瓦斯爆炸易发性的分类标准,构建煤矿瓦斯爆炸易发性评估的经典域、节域和物元;然后,为了避免确定指标权重的人为主观因素的影响,提出用简单关联函数确定指标权重;最后,计算煤矿瓦斯爆炸易发性的关联函数值和关联度,确定瓦斯爆炸易发性的等级及其变量特征值。经计算,煤矿爆炸易发性的可拓评估结果为"很小"等级。同时,为了验证可拓评估结果的合理性,将其与模糊评估进行比较,两者所得评估结果相一致。从而表明:将可拓学应用于煤矿瓦斯爆炸易发性评估是合理可行的。     

Ethoxylated Soybean Polyols for Polyurethanes

Soybean polyols prepared by ring opening reactions of epoxidized soybean oil with hydrogen active compounds (water, alcohols, organic or inorganic acids, thiols, hydrogen etc.) have a low reactivity in the reaction with isocyanates because the hydroxyl groups are secondary. This paper presents a simple and convenient method to increase the reactivity of soybean polyols with secondary hydroxyl groups by ethoxylation reactions with the preservation of triglyceride ester bonds. The method uses mild reaction conditions: low alkoxylation temperature of 35–45 °C, low pressure of 0.1–0.2 MPa (15–30 p.s.i.) and a superacid as catalyst (HBF₄). The new soybean polyols have a higher reactivity toward isocyanates in polyurethane formation due to the high percentage of primary hydroxyl groups. The primary hydroxyl content was determined by the second order kinetics of polyol reaction with phenyl isocyanate.     

Chemical Treatments of Natural Fiber for Use in Natural Fiber-Reinforced Composites: A Review

Studies on the use of natural fibers as replacement to man-made fiber in fiber-reinforced composites have increased and opened up further industrial possibilities. Natural fibers have the advantages of low density, low cost, and biodegradability. However, the main disadvantages of natural fibers in composites are the poor compatibility between fiber and matrix and the relative high moisture sorption. Therefore, chemical treatments are considered in modifying the fiber surface properties. In this paper, the different chemical modifications on natural fibers for use in natural fiber-reinforced composites are reviewed. Chemical treatments including alkali, silane, acetylation, benzoylation, acrylation, maleated coupling agents, isocyanates, permanganate and others are discussed. The chemical treatment of fiber aimed at improving the adhesion between the fiber surface and the polymer matrix may not only modify the fiber surface but also increase fiber strength. Water absorption of composites is reduced and their mechanical properties are improved.     

Status of recycling end-of-life vehicles and efforts to reduce automobile shredder residues in Korea

The present end-of-life vehicle (ELV) recycle rate and management status during the dismantling stage were investigated to aid the establishment of policies for the management of ELVs by surveying information and using the results gained from questionnaires given to dismantlers. The average recycle rate at the dismantling stage was 44% of the mass of a new vehicle and the rest of the ELV was then compressed and transported to shredding companies to recover mainly the iron content, which averaged 38.7% of the mass of a new vehicle. Nonferrous metals such as copper, antimony, zinc, and aluminum accounted for only 1.5%. The automobile shredder residues (ASRs) were composed of light and heavy fluffs and soil/dust and amounted to 15.8% based on the mass of a new vehicle. The dumping of fluff and inorganic residues in landfill sites, however, will be restricted when new regulations are implemented to reduce the disposal amount to less than 5% of a new car, as has been done in European countries and in Japan. The detailed characteristics of ASR were investigated to suggest appropriate means of treatment such as volume reduction or the utilization of thermal technologies to meet future expected enforcement. Also, some concerns on hazardous pollutant release such as that of dioxins while utilizing such thermal treatment methods were considered. The present on-going research and development projects to meet such future management targets are also introduced.     

Material flow indicators to measure progress toward a sound material-cycle society

This article reviews recent progress in material flow analysis and its use in providing resource productivity indicators and is based on developments in Japanese policy toward a sound material-cycle society and in international forums such as within the Organisation for Economic Development and Cooperation, covering both institutional and methodological issues. Indicators derived from economy-wide material flow accounts such as direct material inputs are useful to demonstrate the absolute size of a physical economy and to reinforce the need to both reduce consumption of natural resources and limit waste generation. Interpretation of material flows as resources and potential environmental impacts is discussed, and linkages between the size of material flows and specific environmental impacts and damage must be further elaborated for use in environmental policy. Lessons learned from the practical use of resource productivity indicators are also discussed. Additional indicators are needed that can be used to evaluate the performance of microeconomic contributors. The need for an integrated approach that links upstream resource issues and downstream waste issues through the 3Rs concept or the circular economy/society concept is attracting increasing attention. Consequently, the accumulation of reliable scientific knowledge and data in this field in a fully international context is essential.     

Study of Fatigue Life and Filler Interaction of Paper Sludge Filled Epoxidized Natural Rubber (ENR) and Maleated Natural Rubber (MNR) Composites

An investigation on the effect of epoxidation and maleated natural rubber (MNR) on fatigue and rubber-filler interaction properties of paper sludge filled natural rubber composites was elucidated. Paper sludge loading was varied from 0 to 40 phr and conventional vulcanisation system was used while compounding was carried out on a laboratory sized two roll mill. Two different types of natural rubber, SMR L and ENR 50 having 0 and 50 mole% of epoxidation were used in order to investigate the effect of epoxidation on the composites. Results indicate that, at a fixed filler loading, ENR 50 vulcanizates exhibit higher fatigue life than SMR L vulcanizates especially at filler loading below 20 phr which might be associated with better rubber-filler interaction. In the case of composites with the addition of maleated natural rubber (MNR), a higher fatigue life was observed due to presence of physical and/or chemical linkages, which increases the interfacial adhesion. Scanning electron microscopy (SEM) micrographs of fatigue fracture surfaces and rubber-filler interaction study supported the observed result on fatigue life.     

Photodegradation of tetraphenyltin contained in polychlorinated biphenyl-based transformer oil simulants in alkaline 2-propanol solution

The photodegradation of tetraphenyltin (TePT) contained in polychlorinated biphenyl (PCB)-based transformer oil simulants by ultraviolet (UV) irradiation in alkaline 2-propanol solutions was examined. In the absence of PCBs, the TePT level fell to below 1% of the initial concentration within 30 min. In the absence of both PCBs and an alkali, the concentrations of tri-, di-, and monophenyltins initially increased to a few milligrams per liter, and then reduced to below the detection limits within 90 min. The addition of an alkali to the reaction solution slightly accelerated the photodecomposition of TePT. The decomposition of other phenyltins (PTs) was also accelerated. When PCBs with concentrations of approximately 80 times the initial TePT concentration were added, only a small fraction of the TePT decomposed within 100 min. Moreover, the levels of PTs did not change during irradiation. TePT and other PTs did decompose when the level of PCBs was reduced to the same concentration as that of TePT; however, the decomposition rates were slower than those in the absence of PCBs. In the actual treatment process, TePT and other PTs in PCB-based transformer oil are decomposed by catalytic reduction, which is used after UV irradiation. Therefore, in the actual treatment of PCB-based transformer oil wastes, pollution due to PTs can be prevented.     

Characterization and recycling of polymeric components present in cell phones

The cell phone market is developing at a rapid speed. Today there are more than 1.6 billion consumers in the world, and the lifetime of a cell phone is less than 2 years. As a consequence, there is an increase in the waste associated to this product, and many alternatives to the disposal of the cell phones are being studied, such as recycling which shows to be the most important. It is crucial to know what materials constitute the cell phone in order to carry out recycling and determine environmental and economical issues. This work presents an evaluation of the cell phone components, characterizing the raw materials and some properties of the recycled materials.     

Biodegradation of Polycaprolactone Powders Proposed as Reference Test Materials for International Standard of Biodegradation Evaluation Method

Polycaprolactone (PCL) powders were prepared from PCL pellets using a rotation mechanical mixer. PCL powders were separated by sieves with 60 and 120 meshes into four classes; 0–125 μm, 125–250 μm, 0–250 μm and 250–500 μm. Biodegradation tests of PCL powders and cellulose powders in an aqueous solution at 25°C were performed using the coulometer according to ISO 14851. Biodegradation tests of PCL powders and cellulose powders in controlled compost at 58°C were performed by the Mitsui Chemical Analysis and Consulting Service, Inc. according to ISO 14855-1 and by using the Microbial Oxidative Degradation Analyzer (MODA) instrument according to ISO/DIS 14855-2. PCL powders were faster biodegraded than cellulose powders. The reproducibility of biodegradation of PCL powders is excellent. Differences in the biodegradation of PCL powders with different class were not observed by the ISO 14851 and ISO/DIS 14855-2. An enzymatic degradation test of PCL powders with different class was studied using an enzyme of Amano Lipase PS. PCL with smaller particle size was faster degraded by the enzyme. PCL powders with regulated sizes from 125 μm to 250 μm are proposed as a reference material for the biodegradation test.